1.将装好胶水的针筒放入针筒夹持器后并固定。比如装AB胶，将A胶和B胶分别从压力桶接到胶枪A、B进胶口，A、B胶分别通过三通到混合管时开始混合，胶水混合程度由混合管长度决定，只需控制压杆即可控制胶水通断，由一连串左右旋叶片相互垂直排列在套管内组成，A、B胶水经过混合管时进行连续的切割与重合为均匀的混合液，以保证出胶量精确。
1. Put the syringe loaded with glue into the syringe holder and fix it. For example, install AB glue, connect glue a and B from the pressure barrel to the glue inlet of glue gun a and B respectively, and the glue a and B begin to mix when they pass through the three-way to the mixing pipe respectively. The mixing degree of glue is determined by the length of the mixing pipe. Just control the pressure rod to control the on-off of glue, which is composed of a series of left and right rotating blades vertically arranged in the casing, a B. when the glue passes through the mixing pipe, it shall be continuously cut and overlapped into a uniform mixing liquid to ensure the accurate glue output.
2.连接气阀，将点胶机的点胶控制器口通过气管连接到针筒，并把针筒气阀连接到点胶控制器的AIRIN，并且连接点胶机和点胶控制器的电缆线。
2. Connect the air valve, connect the dispensing controller port of the dispensing machine to the syringe through the air pipe, connect the syringe air valve to the airin of the dispensing controller, and connect the cable between the dispensing machine and the dispensing controller.

3.将点胶机的点胶接口通过电缆线连接到点胶控制器的信号输入接口，把脚踏板连接到点胶机的运行接口上，以控制点胶机的运行。将Z轴的连接电缆插头与点胶机Z轴连接。如所用点胶控制器同点胶机的连接器型号相同，可以根据连接器的芯数不同来看出点胶机的点胶和运行等连接口，二芯点胶，三芯运行。
3. Connect the dispensing interface of the dispensing machine to the signal input interface of the dispensing controller through cable, and connect the foot pedal to the operation interface of the dispensing machine to control the operation of the dispensing machine. Connect the connecting cable plug of the z-axis with the z-axis of the dispensing machine. If the dispensing controller used is the same as the connector model of the dispensing machine, you can see the connection ports of dispensing and operation of the dispensing machine, two core dispensing and three core operation according to the number of cores of the connector.
4.将手持式编程器通过串口线选择到点胶机左侧的接口上，如果所用点胶控制器同点胶机背面的连接器型号不相同，可以根据点胶控制器的说明书进行电缆线的配制和连接。
4. Select the hand-held programmer to the interface on the left side of the dispensing machine through the serial port cable. If the dispensing controller used is different from the connector model on the back of the dispensing machine, the cable can be prepared and connected according to the instructions of the dispensing controller.
本文由双组份打胶机友情奉献.更多有关的知识请点击:http://linshi.jncsjx.com我们将会对您提出的疑问进行详细的解答，欢迎您登录网站留言.
This article is dedicated by the two-component glue applicator. For more information, please click: http://linshi.jncsjx.com We will answer your questions in detail. You are welcome to log in to the website and leave a message